Renishaw FANUC 31使用中內孔測量程式

yit02yit02

Renishaw FANUC 31使用中內孔測量程式
%
8 b& i! B' m% M- x* q2 O<CEN-4-3>
G91G30Z0
G54
G90G0X0Y0
; v7 D. e5 [* `G43H01Z100.
(四點測量0度為起點A直徑XY為孔位S為數據指令M安全距離F安全高度)
G65P9656A0.R60.X0.Y0Z-5.S0M5.F100.
G0G90X0Y22.5
( j7 P& V7 Y) C- I: R$ v8 m: g  b#702=#108
#703=#118
M01
# f& F4 i& Z# p* J" S  L(三點測量90度為起點A直徑XY為孔位S為數據指令M安全距離F安全高度)
$ R- S! y+ o/ A! w' u5 N9 ]G65P9654A90.R60.X0.Y0Z-5.S0M5.F100.
* n& D6 |: e8 M3 gG0G90X0Y22.5
* Q) X* p2 q1 r% f: p/ R5 R# m/ i* X#704=#108
6 e" h9 M/ y! N+ L- U  b#705=#118
M01
G91G30Z0
G90X0Y0
M30
%

6 u: V" |6 Y$ D+ W% e- z#108→實測尺寸
% c+ {$ u! [3 ], v* k* t+ m) R% n#118→實測尺寸公差

0 K4 F! \7 \* j1 L
. P8 S" p8 }! G& U# q& A%
2 J- k3 s/ K, F: U3 y: Q3 j7 w) XO9654(* HOLE MEASURING 3 POINTS)
G53
IF[#3008EQ1]GOTO999(PROGRAM RESTART)
/ S+ J, n  ?4 U#125=#4000(MAIN PRG NO.)
#126=#4115(MACRO-NO.)
+ g" K6 Z  ]1 `. j2 V1 }, yM98P9608(AMCS START)
#31=-3
1 l5 S- L& @% ]M98P9615(PATTERN MEASURING)
2 H6 P  _# |1 d9 B/ ~4 @+ \M98P9609(AMCS END)
M98P9601(HOLE & BOSS DATA)
* n( s& @; c' E# q, nM98P9600(PROCESS)
N999M99
9 g  s0 S( ]8 E( I5 c& Y9 G, R. r
; v/ g+ W+ g8 U) U%
* W+ q# d3 ]/ Q
- l$ p1 O& D$ D. M7 R8 G
%
& P6 p, I# m  A* i4 z3 A9 M7 W2 W  XO9656(* HOLE MEASURING 4 POINTS)
G53
# d! Y3 n' ~. T: ]) P% {& ^  NIF[#3008EQ1]GOTO999(PROGRAM RESTART)
#125=#4000(MAIN PRG NO.)
#126=#4115(MACRO-NO.)
' j) s  x( k1 D! k4 M. YM98P9608(AMCS START)
#31=-4
M98P9615(PATTERN MEASURING)
( G' {, r+ S" H$ R, CM98P9609(AMCS END)
$ H5 I; E& P# t% v* tM98P9601(HOLE & BOSS DATA)
M98P9600(PROCESS)
4 z9 A0 [% w. g  B; u$ EN999M99
/ j- b1 `" s( z2 U& A
%