Renishaw FANUC 31使用中內孔測量程式

yit02yit02

Renishaw FANUC 31使用中內孔測量程式
%
% _, J1 j4 H: n; ^2 N<CEN-4-3>
G91G30Z0
: [% p8 S! P5 _& v, ZG54
$ C% r9 J' _" x1 eG90G0X0Y0
* P$ t1 D1 ?" }% J3 C3 mG43H01Z100.
(四點測量0度為起點A直徑XY為孔位S為數據指令M安全距離F安全高度)
G65P9656A0.R60.X0.Y0Z-5.S0M5.F100.
G0G90X0Y22.5
#702=#108
( Q6 {1 ^2 g6 ^- e! \. M#703=#118
' G1 d/ H5 E7 \4 gM01
(三點測量90度為起點A直徑XY為孔位S為數據指令M安全距離F安全高度)
G65P9654A90.R60.X0.Y0Z-5.S0M5.F100.
G0G90X0Y22.5
#704=#108
#705=#118
M01
& g0 y7 W! }6 C+ D: E" U% PG91G30Z0
( H3 @9 ]4 ~( Y8 w! aG90X0Y0
" W! ~' c8 ~$ h; `" {% t) s! kM30
%
8 u' B) l7 S3 ~( i4 R- [( k
4 B7 Q( u: ?( e2 o#108→實測尺寸
% X4 `! b# e% D" L#118→實測尺寸公差
- ~$ C! M5 L. I  H; c. `; z
$ Y+ \$ Z$ p* G! |8 D0 ^
%
O9654(* HOLE MEASURING 3 POINTS)
, H" ]$ Q5 i! b+ v$ F/ ^G53
IF[#3008EQ1]GOTO999(PROGRAM RESTART)
* l/ p  m& o, z#125=#4000(MAIN PRG NO.)
/ X5 W$ B/ n0 _) J9 D  Q$ n#126=#4115(MACRO-NO.)
M98P9608(AMCS START)
#31=-3
6 z) ~  d, b5 D8 wM98P9615(PATTERN MEASURING)
M98P9609(AMCS END)
M98P9601(HOLE & BOSS DATA)
  ]# g2 G8 F$ T( L/ qM98P9600(PROCESS)
N999M99
: j& ]9 |- T8 E$ @# \
%
; ~# V& y; h- R" T0 M
: Y' P+ n( ~( ^/ j. {, C, M/ f
%
O9656(* HOLE MEASURING 4 POINTS)
& T- ~. W' [2 E+ D( q# UG53
IF[#3008EQ1]GOTO999(PROGRAM RESTART)
#125=#4000(MAIN PRG NO.)
#126=#4115(MACRO-NO.)
M98P9608(AMCS START)
#31=-4
, U5 S# e6 I: J8 N* y) AM98P9615(PATTERN MEASURING)
5 u% i2 N6 K  Q$ v' {% C' L5 _M98P9609(AMCS END)
, }0 o) D/ p' @. |5 T$ S' g4 EM98P9601(HOLE & BOSS DATA)
M98P9600(PROCESS)
% o" r& t) t3 U1 |N999M99
6 u/ t3 c* E0 S+ ^3 R: a
%